P061B-86 Internal Control Module Torque Calculation Performance - Signal invalid

Electrical Cause

No

Mechanical Cause

No

Control Module Cavity

Not applicable

Monitor Description

Due to an internal software error, an inertia start request is being sent when correct conditions are not met

Prioritized List of Possible Causes

Powertrain control module software is not at the latest version

Powertrain control module internal failure

Prioritized Checks to Perform

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Update ECU

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new powertrain control module and run application - ECU Diagnostics / Powertrain Control Module (PCM) / Replace ECU

P061C-00 Internal Control Module Engine RPM Performance - No sub type information

Monitor Description

Desired ignition angle is not plausible

Prioritized List of Possible Causes

Powertrain control module power or ground circuit open circuit, high resistance

Powertrain control module software fault

Powertrain control module internal failure

Prioritized Checks to Perform

Refer to the electrical circuit diagrams and check the powertrain control module power and ground circuits for open circuit, high resistance. Check the electrical connectors for evidence of water ingress. Check the terminals for damage and corrosion. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Update ECU

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new powertrain control module: Run application - ECU Diagnostics / Powertrain Control Module (PCM) / Replace ECU

P061D-42 Internal Control Module Engine Air Mass Performance - General memory failure

Monitor Description

Injector cut off patterns found not plausible

Prioritized List of Possible Causes

Powertrain control module power or ground circuit open circuit, high resistance

Powertrain control module software fault

Powertrain control module internal failure

Prioritized Checks to Perform

Refer to the electrical circuit diagrams and check the powertrain control module power and ground circuits for open circuit, high resistance. Check the electrical connectors for evidence of water ingress. Check the terminals for damage and corrosion. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Update ECU

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new powertrain control module: Run application - ECU Diagnostics / Powertrain Control Module (PCM) / Replace ECU

P061D-43 Internal Control Module Engine Air Mass Performance - Special memory failure

Monitor Description

Desired fueling control limits are implausible

Prioritized List of Possible Causes

Powertrain control module power or ground circuit open circuit, high resistance

Powertrain control module software fault

Powertrain control module internal failure

Prioritized Checks to Perform

Refer to the electrical circuit diagrams and check the powertrain control module power and ground circuits for open circuit, high resistance. Check the electrical connectors for evidence of water ingress. Check the terminals for damage and corrosion. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Update ECU

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new powertrain control module: Run application - ECU Diagnostics / Powertrain Control Module (PCM) / Replace ECU

P061D-62 Internal Control Module Engine Air Mass Performance - Signal compare failure

Monitor Description

Predicted air mass was found not plausible

Prioritized List of Possible Causes

Powertrain control module power or ground circuit open circuit, high resistance

Powertrain control module software fault

Powertrain control module internal failure

Prioritized Checks to Perform

Refer to the electrical circuit diagrams and check the powertrain control module power and ground circuits for open circuit, high resistance. Check the electrical connectors for evidence of water ingress. Check the terminals for damage and corrosion. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Update ECU

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new powertrain control module: Run application - ECU Diagnostics / Powertrain Control Module (PCM) / Replace ECU

P061F-00 Internal Control Module Throttle Actuator Controller Performance - No sub type information

Electrical Cause

No

Mechanical Cause

Yes

Control Module Cavity

Not applicable

Monitor Description

Measured throttle position deviates from requested position excessively

Prioritized List of Possible Causes

Throttle actuator related fault

Throttle actuator obstructed

Throttle actuator failure

Vehicle Conditions to Enable DTC Setting Strategy

Ignition off. Ignition on. Wait 60 seconds. Start the engine. Limp home position check will be performed if the blade does not achieve a position close to the learnt limp home position. A fault is set as the throttle is faulty

Prioritized Checks to Perform

Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for throttle actuator related Diagnostic Trouble Code(s) and perform the relevant corrective actions

Check the throttle body for obstructions. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new throttle actuator

P0627-07 Fuel Pump "A" Control Circuit/Open - Mechanical failures

Electrical Cause

Yes

Mechanical Cause

Yes

Monitor Description

To detect a fault on low pressure pump

Prioritized List of Possible Causes

Low pressure fuel pump circuit short circuit to ground, short circuit to power, open circuit, high resistance

Low pressure fuel pump failure

Vehicle Conditions to Enable DTC Setting Strategy

Ignition on

Prioritized Checks to Perform

Refer to the electrical circuit diagrams and check the low pressure fuel pump circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Check the electrical connectors for evidence of water ingress. Check the terminals for damage and corrosion. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new low pressure fuel pump

P062A-31 Fuel Pump "A" Control Circuit Range/Performance - No signal

Electrical Cause

Yes

Mechanical Cause

Yes

Monitor Description

To detect a fault on low pressure pump

Prioritized List of Possible Causes

Fuel pump driver module signal circuit short circuit to ground, short circuit to power, open circuit, high resistance

Fuel pump driver module failure

Vehicle Conditions to Enable DTC Setting Strategy

Ignition on

Prioritized Checks to Perform

Refer to the electrical circuit diagrams and check the fuel pump driver module signal circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Check the electrical connectors for evidence of water ingress. Check the terminals for damage and corrosion. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new fuel pump driver module

P062F-00 Internal Control Module EEPROM Error - No sub type information

Electrical Cause

No

Mechanical Cause

No

Monitor Description

The fault is set when at least three software blocks cannot be read

Prioritized List of Possible Causes

Powertrain control module internal failure

Prioritized Checks to Perform

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new powertrain control module: Run application - ECU Diagnostics / Powertrain Control Module (PCM) / Replace ECU

P062F-43 Internal Control Module EEPROM Error - Special memory failure

Electrical Cause

No

Mechanical Cause

No

Monitor Description

The fault is set when one software block can not be written more than 3 times

Prioritized List of Possible Causes

Powertrain control module internal failure

Prioritized Checks to Perform

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new powertrain control module: Run application - ECU Diagnostics / Powertrain Control Module (PCM) / Replace ECU

P0633-00 Immobilizer Key Not Programed - ECM/PCM - No sub type information

Electrical Cause

No

Mechanical Cause

No

Monitor Description

Signals an error reading or writing the Target ID (TID) to the PCM EEPROM

Prioritized List of Possible Causes

Body control module power or ground circuit open circuit, high resistance

Powertrain control module power or ground circuit open circuit, high resistance

Instrument cluster software is not at the latest version

Powertrain control module software is not at the latest version

Security key invalid

Powertrain control module internal failure

Prioritized Checks to Perform

Refer to the electrical circuit diagrams and check the body control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary

Refer to the electrical circuit diagrams and check the powertrain control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Instrument Panel Cluster Control Module (IPC) / Update ECU

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Update ECU

Using the Jaguar Land Rover approved diagnostic equipment, run application - Service / Body Control Module (BCM): Immobilization

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new powertrain control module: Run application - ECU Diagnostics / Powertrain Control Module (PCM) / Replace ECU

P0634-00 Control Module Internal Temperature "A" Too High - No sub type information

Electrical Cause

Yes

Mechanical Cause

Yes

Control Module Cavity

Circuit reference - O_T_ECM -

Monitor Description

A defect is detected when internal powertrain control module temperature is greater than 119°C

Prioritized List of Possible Causes

Powertrain control module cooling fan airflow obstructed

Powertrain control module cooling fan circuit short circuit to ground, short circuit to power, open circuit, high resistance

Powertrain control module cooling fan failure

Vehicle Conditions to Enable DTC Setting Strategy

Ignition on, start engine and idle for 30 seconds

Prioritized Checks to Perform

Check the powertrain control module cooling fan airflow for obstructions. Rectify as necessary

Inspect connectors for signs of water ingress and pins for damage and/or corrosion

Refer to the electrical circuit diagrams and check the powertrain control module cooling fan circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Check the electrical connectors for evidence of water ingress. Check the terminals for damage and corrosion. Repair the wiring harness as necessary

Install a new powertrain control module cooling fan

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest

P064A-42 Fuel Pump Control Module "A" - General memory failure

Prioritized List of Possible Causes

Fuel pump driver module diagnostic circuit short circuit to ground, short circuit to power, open circuit

Fuel pump driver module failure

Prioritized Checks to Perform

Refer to the electrical circuit diagrams and check the fuel pump driver module diagnostic circuit for short circuit to ground, short circuit to power, open circuit. Check the electrical connectors for evidence of water ingress. Check the terminals for damage and corrosion. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new fuel pump driver module

P064A-98 Fuel Pump Control Module "A" - Component or system over temperature

Prioritized List of Possible Causes

Fuel pump driver module diagnostic circuit short circuit to ground, short circuit to power, open circuit

Fuel pump driver module failure

Prioritized Checks to Perform

Refer to the electrical circuit diagrams and check the fuel pump driver module diagnostic circuit for short circuit to ground, short circuit to power, open circuit. Check the electrical connectors for evidence of water ingress. Check the terminals for damage and corrosion. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new fuel pump driver module

P064D-01 Internal Control Module O2 Sensor Processor Performance Bank 1 - General electrical failure

Prioritized List of Possible Causes

Powertrain control module internal failure

Prioritized Checks to Perform

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new powertrain control module: Run application - ECU Diagnostics / Powertrain Control Module (PCM) / Replace ECU

P064D-02 Internal Control Module O2 Sensor Processor Performance Bank 1 - General signal failure

Prioritized List of Possible Causes

Powertrain control module internal failure

Prioritized Checks to Perform

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new powertrain control module: Run application - ECU Diagnostics / Powertrain Control Module (PCM) / Replace ECU

P0658-00 Actuator Supply Voltage "A" Circuit Low - No sub type information

Prioritized List of Possible Causes

Other related Diagnostic Trouble Code(s)

Battery fault

Charging system fault

Powertrain control module power or ground circuit open circuit, high resistance

Prioritized Checks to Perform

Check powertrain control module for related Diagnostic Trouble Code(s) and refer to relevant DTC index

Refer to the relevant section of the workshop manual and check the battery. Rectify as necessary

Refer to the relevant section of the workshop manual and check the charging system. Using the Jaguar Land Rover approved diagnostic equipment, check the battery charger control module or the direct current to direct current converter for related Diagnostic Trouble Code(s) and refer to the relevant DTC index

Refer to the electrical circuit diagrams and check the powertrain control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest

P0659-00 Actuator Supply Voltage "A" Circuit High - No sub type information

Prioritized List of Possible Causes

Other related Diagnostic Trouble Code(s)

Vehicle battery over charged

Charging system fault - over charging

Generator circuit short circuit to ground, short circuit to power, open circuit, high resistance

Powertrain control module main fuse mechanical integrity

Connector is disconnected, connector pin is backed out, connector pin corrosion

Harness failure - Wiring integrity short circuit to ground, short circuit to power, open circuit, high resistance

Prioritized Checks to Perform

Check powertrain control module for related Diagnostic Trouble Code(s) and refer to relevant DTC index

Check the vehicle charging system performance to make sure the voltage regulation is correct

Refer to the electrical circuit diagrams and check the generator circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary

Check powertrain control module main fuse for mechanical integrity

Inspect connectors for signs of water ingress and pins for damage and/or corrosion

Refer to the electrical circuit diagrams and check connections are secure and wiring integrity

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest

P0686-11 ECM/PCM Power Relay Control Circuit Low - Circuit short to ground

Control Module Cavity

Circuit reference - O_S_MRLY -

Prioritized List of Possible Causes

The powertrain control module has detected a ground measurement for a period longer than expected or has detected a ground measurement when another value was expected

Engine management system relay power and ground circuits open circuit

Engine management system relay circuit short circuit to ground, short circuit to power, open circuit, high resistance

Connector is disconnected, connector pin is backed out, connector pin corrosion

Engine management system relay failure

Prioritized Checks to Perform

Refer to the electrical circuit diagrams and check engine management system relay power and ground circuits for open circuit

Refer to the electrical circuit diagrams and check the engine management system relay circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary

Inspect connectors for signs of water ingress and pins for damage and/or corrosion

Install a new engine management system relay

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest

P0687-24 ECM/PCM Power Relay Control Circuit High - Signal stuck high

Prioritized List of Possible Causes

Power distribution fault

Powertrain control module power relay circuit short circuit to power

Prioritized Checks to Perform

Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for other power distribution related Diagnostic Trouble Code(s) and perform the relevant corrective actions

Refer to the electrical circuit diagrams and check the powertrain control module power relay circuit for short circuit to power. Repair the wiring harness as necessary

P068A-00 ECM/PCM Power Relay De-Energized Performance - Too Early - No sub type information

Monitor Description

This DTC is set when the engine management system high current relay contacts open early - Indicating a power hold failure

Prioritized List of Possible Causes

Powertrain control module power or ground circuit open circuit, high resistance

Battery terminal clamps loose

Battery disconnected before the engine management system relay has opened

Engine management system relay circuit short circuit to ground, open circuit, high resistance

Powertrain control module power relay failure

Prioritized Checks to Perform

Refer to the electrical circuit diagrams and check the powertrain control module power and ground circuits for open circuit, high resistance. Repair the wiring harness as necessary

Check the integrity of the battery terminal clamps. Rectify as necessary

Check that the battery has not been disconnected before the engine management system relay has opened

Refer to the electrical circuit diagrams and check the engine management system relay circuit for short circuit to ground, open circuit, high resistance. Repair the wiring harness as necessary

Install a new relay

P06A6-00 Sensor Reference Voltage "A" Circuit Range/Performance - No sub type information

Electrical Cause

Yes

Mechanical Cause

No

Control Module Cavity

Circuit reference - O_V_5VRAILPS -

Circuit reference - O_5VCLNTP -

Circuit reference - O_V_5VMAP -

Circuit reference - O_V_5VBPS -

Circuit reference - O_V_5VCRS -

Circuit reference - O_V_5VLPEGR -

Circuit reference - O_V_5VAPP1 -

Circuit reference - O_V_5VWGPT -

Circuit reference - O_V_5VAMS -

Prioritized List of Possible Causes

Powertrain control module sensor 5 volt supply circuit short circuit to ground, short circuit to power, open circuit

Connector is disconnected, connector pin is backed out, connector pin corrosion

Prioritized Checks to Perform

Refer to electrical circuit diagrams and check the powertrain control module sensor 5 volt supply circuit for short circuit to ground, short circuit to power, open circuit. Repair the wiring harness as necessary

Inspect connectors for signs of water ingress and pins for damage and/or corrosion

P06A7-00 Sensor Reference Voltage "B" Circuit Range/Performance - No sub type information

Electrical Cause

Yes

Mechanical Cause

No

Control Module Cavity

Circuit reference - O_V_5VGPFDP -

Circuit reference - O_V_5VFLPS -

Circuit reference - O_V_5VFTPS -

Circuit reference - O_V_5VCLUPOT -

Circuit reference - O_V_5VAPP2 -

Circuit reference - O_V_5VLPEGRDP -

Prioritized List of Possible Causes

Powertrain control module sensor 5 volt supply circuit short circuit to ground, short circuit to power, open circuit

Connector is disconnected, connector pin is backed out, connector pin corrosion

Prioritized Checks to Perform

Refer to electrical circuit diagrams and check the powertrain control module sensor 5 volt supply circuit for short circuit to ground, short circuit to power, open circuit. Repair the wiring harness as necessary

Inspect connectors for signs of water ingress and pins for damage and/or corrosion

P06A8-00 Sensor Reference Voltage "C" Circuit Range/Performance - No sub type information

Electrical Cause

Yes

Mechanical Cause

No

Control Module Cavity

Circuit reference - O_V_5PHEV -

Circuit reference - O_V_5VTVA -

Circuit reference - O_V_5VGPS -

Prioritized List of Possible Causes

Powertrain control module sensor 5 volt supply circuit short circuit to ground, short circuit to power, open circuit

Connector is disconnected, connector pin is backed out, connector pin corrosion

Prioritized Checks to Perform

Refer to electrical circuit diagrams and check the powertrain control module sensor 5 volt supply circuit for short circuit to ground, short circuit to power, open circuit. Repair the wiring harness as necessary

Inspect connectors for signs of water ingress and pins for damage and/or corrosion

P06D1-04 Internal Control Module Ignition Coil Control Performance - System internal failures

Prioritized List of Possible Causes

Other ignition coil related Diagnostic Trouble Code(s)

Powertrain control module power and ground circuits open circuit

Powertrain control module internal failure

Prioritized Checks to Perform

Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for ignition coil related Diagnostic Trouble Code(s) and perform the relevant corrective actions

Refer to the electrical circuit diagrams and check the powertrain control module power and ground circuits for open circuit. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest. If the fault persists, install a new powertrain control module and run application - ECU Diagnostics / Powertrain Control Module (PCM) / Replace ECU

P06DA-13 Engine Oil Pressure Control Circuit/Open - Circuit open

Electrical Cause

Yes

Mechanical Cause

Yes

Control Module Cavity

Circuit reference - O_T_OILP -

Prioritized List of Possible Causes

Connector is disconnected, connector pin is backed out, connector pin corrosion

Variable oil pump solenoid fuse failure

Variable oil pump solenoid circuit short circuit to ground, short circuit to power, open circuit, high resistance

Variable oil pump solenoid failure

Vehicle Conditions to Enable DTC Setting Strategy

Ignition on, engine running

Prioritized Checks to Perform

Inspect connectors for signs of water ingress and pins for damage and/or corrosion

Check the integrity of the variable oil pump solenoid fuse. Rectify as necessary

Refer to the electrical circuit diagrams and check the variable oil pump solenoid circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary

Install a new variable oil pump solenoid

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest

P06DA-4B Engine Oil Pressure Control Circuit/Open - Over temperature

Electrical Cause

Yes

Mechanical Cause

Yes

Control Module Cavity

Circuit reference - O_T_OILP -

Prioritized List of Possible Causes

Connector is disconnected, connector pin is backed out, connector pin corrosion

Variable oil pump solenoid fuse failure

Variable oil pump solenoid circuit short circuit to ground, short circuit to power, open circuit, high resistance

Variable oil pump solenoid failure

Vehicle Conditions to Enable DTC Setting Strategy

Ignition on, engine running

Prioritized Checks to Perform

Inspect connectors for signs of water ingress and pins for damage and/or corrosion

Check the integrity of the variable oil pump solenoid fuse. Rectify as necessary

Refer to the electrical circuit diagrams and check the variable oil pump solenoid circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary

Install a new variable oil pump solenoid

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest

P06DB-11 Engine Oil Pressure Control Circuit Low - Circuit short to ground

Electrical Cause

Yes

Mechanical Cause

Yes

Control Module Cavity

Circuit reference - O_T_OILP -

Prioritized List of Possible Causes

Connector is disconnected, connector pin is backed out, connector pin corrosion

Variable oil pump solenoid fuse failure

Variable oil pump solenoid circuit short circuit to ground, short circuit to power, open circuit, high resistance

Variable oil pump solenoid failure

Vehicle Conditions to Enable DTC Setting Strategy

Ignition on, engine running

Prioritized Checks to Perform

Inspect connectors for signs of water ingress and pins for damage and/or corrosion

Check the integrity of the variable oil pump solenoid fuse. Rectify as necessary

Refer to the electrical circuit diagrams and check the variable oil pump solenoid circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary

Install a new variable oil pump solenoid

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest

P06DC-12 Engine Oil Pressure Control Circuit High - Circuit short to battery

Electrical Cause

Yes

Mechanical Cause

Yes

Control Module Cavity

Circuit reference - O_T_OILP -

Prioritized List of Possible Causes

Connector is disconnected, connector pin is backed out, connector pin corrosion

Variable oil pump solenoid fuse failure

Variable oil pump solenoid circuit short circuit to ground, short circuit to power, open circuit, high resistance

Variable oil pump solenoid failure

Vehicle Conditions to Enable DTC Setting Strategy

Ignition on, engine running

Prioritized Checks to Perform

Inspect connectors for signs of water ingress and pins for damage and/or corrosion

Check the integrity of the variable oil pump solenoid fuse. Rectify as necessary

Refer to the electrical circuit diagrams and check the variable oil pump solenoid circuit for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary

Install a new variable oil pump solenoid

Using the Jaguar Land Rover approved diagnostic equipment, run application - ECU Diagnostics / Powertrain Control Module (PCM) / Clear Diagnostic Trouble Code(s). Retest