INGENIUM I4 2.0L Diesel/INGENIUM I4 2.0L Petrol, Vehicles With: 9HP50

P0725-81 Engine Speed Input Circuit - Invalid serial data received

Engine system fault

NOTE:

No repair actions relating to the Transmission or Transmission Control Module will rectify this fault

Prioritized steps to perform:

Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related DTCs and refer to the relevant DTC index

P0726-21 Engine Speed Input Circuit Range/Performance - Signal amplitude < Minimum>

Engine detected to be close to stall

Engine or powertrain control module failure

NOTE:

If this DTC is set, DO NOT replace any transmission components (for example: transmission control module, valve block or gearbox). This DTC does not indicate a transmission issue.

Prioritized steps to perform:

Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for latest level software and update as required

Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control module for latest level software and update as required

Using the Jaguar Land Rover approved diagnostic equipment, check the powertrain control module for related DTCs and refer to the relevant DTC index

If the fault persists, raise a Technical Assist (TA) for further support

P072A-63 Stuck in Neutral - Circuit/component protection time-out

Automatic transmission internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transmission control module with the latest level software

If the fault persists, check the transmission fluid level using the Jaguar Land Rover approved diagnostic equipment to run the 9-speed ZF - Automatic Transmission Fluid Level Check Application. Refer to the relevant section of the workshop manual and check the automatic transmission fluid quality For additional information, refer to: Transmission Oil Color Chart - INGENIUM I4 2.0L Diesel/INGENIUM I4 2.0L Petrol (311-01 Automatic Transmission, Diagnosis and Testing).

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear DTCs and retest

If the fault persists, raise a Technical Assist (TA) for further support

P072F-07 Stuck in Gear 4 - Mechanical failures

Automatic transmission internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transmission control module with the latest level software

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear DTCs and retest

If the fault persists, raise a Technical Assist (TA) for further support

P0730-00 Incorrect Gear Ratio - No sub type information

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

Check the transmission fluid level using the Jaguar Land Rover approved diagnostic equipment to run the 9-speed ZF - Automatic Transmission Fluid Level Check Application. Refer to the relevant section of the workshop manual and check the automatic transmission fluid quality For additional information, refer to: Transmission Oil Color Chart - INGENIUM I4 2.0L Diesel/INGENIUM I4 2.0L Petrol (311-01 Automatic Transmission, Diagnosis and Testing).

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the approved Jaguar Land Rover diagnostic equipment read the adaptions count from the transmission and verify there are at least 4 counts in each clutch. If the transmission is not adapted perform the adaptions procedure

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P0737-62 TCM Engine Speed Output Circuit - Signal compare failure

Transmission control module battery supply

Transmission control module software not at the correct level

Powertrain control module software not at the correct level

NOTE:

No actions relating to Transmission Control Module hardware will resolve this issue

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Using the Jaguar Land Rover approved diagnostic equipment, check the Powertrain Control Module for DTCs

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the Powertrain Control Module with the latest level software

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transmission control module with the latest level software

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs

If problem persists contact technical support

P0737-64 TCM Engine Speed Output Circuit - Signal plausibility failure

Transmission control module battery supply

Transmission control module software not at the correct level

Powertrain control module software not at the correct level

NOTE:

No actions relating to Transmission Control Module hardware will resolve this issue

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Using the Jaguar Land Rover approved diagnostic equipment, check the Powertrain Control Module for DTCs

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the Powertrain Control Module with the latest level software

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transmission control module with the latest level software

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs

If problem persists, contact technical support

P0737-85 TCM Engine Speed Output Circuit - Signal above allowable range

Transmission control module battery supply

Transmission control module software not at the correct level

Powertrain control module software not at the correct level

NOTE:

No actions relating to Transmission Control Module hardware will resolve this issue

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Using the Jaguar Land Rover approved diagnostic equipment, check the Powertrain Control Module for DTCs

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the Powertrain Control Module with the latest level software

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transmission control module with the latest level software

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs

If problem persists, contact technical support

P073E-07 Unable to Engage Reverse - Mechanical failures

Automatic transmission internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Perform multiple Drive to Reverse and Reverse to Drive engagements

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P0741-07 Torque Converter Clutch Circuit Performance / Stuck Off - Mechanical failures

NOTE:

Circuit reference – OUT4 / UDRMV1 –

Torque converter clutch solenoid circuit short circuit to ground, short circuit to power, open circuit, high resistance

Torque converter or automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Refer to the electrical circuit diagrams and check the torque converter clutch solenoid circuit for short circuit to ground. Repair the wiring harness as necessary

Inspect the transmission control module connector and transmission connector for signs of water ingress, pins damage and/or corrosion. Rectify as required

Check the torque converter clutch solenoid circuit internal to transmission between UDRMV1 and ground for short circuit to ground. Rectify as required

Check the torque converter clutch solenoid circuit internal to the transmission between OUT4 and ground for short circuit to ground. Rectify as required

Check and record resistance of the torque converter clutch solenoid circuit internal to the transmission between UDRMV1 and OUT4. If resistance is not in range 4.5 - 6 Ohm, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear DTC and retest

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P0748-11 Pressure Control Solenoid "A" Electrical - Circuit short to ground

NOTE:

Circuit reference – OUT5 / UDRMV1 –

System pressure control valve solenoid circuit short circuit to ground

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Refer to the electrical circuit diagrams and check the system pressure control valve solenoid circuit for short circuit to ground. Repair the wiring harness as necessary

Inspect wiring harness for any damage. Rectify as required

Inspect the transmission control module connector and transmission connector for signs of water ingress, pins damage and/or corrosion. Rectify as required

Check system pressure control valve solenoid internal to transmission between UDRMV1 and ground for short circuit to ground. Rectify as required

Check system pressure control valve solenoid internal to transmission between OUT5 and ground for short circuit to ground. Rectify as required

Check and record resistance of system pressure control valve solenoid internal to transmission between UDRMV1 and OUT5 inside transmission. If resistance is not in range 4.5 - 6 Ohm, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear DTCs and retest

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

P0748-15 Pressure Control Solenoid "A" Electrical - Circuit short to battery or open

NOTE:

Circuit reference – OUT5 / UDRMV1 –

System pressure control valve solenoid circuit short circuit to power, open circuit, high resistance

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Refer to the electrical circuit diagrams and check the system pressure control valve solenoid circuit for short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary

Inspect wiring harness for any damage. Rectify as required

Inspect the transmission control module connector and transmission connector for signs of water ingress, pins damage and/or corrosion. Rectify as required

Check system pressure control valve solenoid internal to transmission between UDRMV1 and ground for short circuit to ground. Rectify as required

Check the system pressure control valve solenoid internal to transmission between UDRMV1 and ground for short circuit to power. Rectify as required

Check the system pressure control valve solenoid internal to transmission between OUT5 and ground for short circuit to ground. Rectify as required

Check the system pressure control valve solenoid internal to transmission between OUT5 and ground for short circuit to power. Rectify as required

Check and record resistance of the system pressure control valve solenoid internal to transmission between UDRMV1 and OUT5 inside transmission. If resistance is not in range 4.5 - 6 Ohm, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear DTCs and retest

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

P077A-92 Output Shaft Speed Sensor Circuit - Loss Of Direction Signal - Performance or incorrect operation

Output shaft speed sensor circuit short circuit to ground, short circuit to power, open circuit, high resistance

Prioritized steps to perform:

Check battery charge and condition

Read all DTCs and investigate any DTCs relating to battery voltage supply

Investigate any DTCs relating to ABS or any communication DTCs

Using the Jaguar Land Rover approved diagnostic equipment check datalogger signal - Transmission Output Shaft (0x1E68)

Check vehicle driveline and engine mounts

Check tires, even wear and matched set

Inspect engine bay wiring harness for damage

Inspect Transmission Control Module connector for damage or water ingress

Refer to the electrical circuit diagrams and check for continuity at the Transmission Control Module connector, between circuit VS_9V - N_T and N_OUT. If the circuit is open circuit or has high resistance, disconnect the transmission connector, and check again for continuity internal to the transmission between circuit VS_9V - N_T and N_OUT.

If the continuity is OK when the transmission connector is disconnected, repair the Transmission Control Module to Transmission wiring harness as necessary

If circuit is open circuit or high resistance contact dealer technical support

Refer to the electrical circuit diagrams and check the VS_9V circuit at the Transmission Control Module for short circuit to ground or short circuit to battery. If short circuit detected, disconnect the transmission connector, and check for short circuit internal to the transmission

If the short circuit is not detected when the transmission connector is disconnected, repair the Transmission Control Module to transmission wiring harness as necessary

If an internal short circuit in the transmission is detected, contact dealer technical support

Refer to the electrical circuit diagrams and check the N_T circuit at the Transmission Control Module for short circuit to ground or short circuit to battery. If short circuit detected, disconnect the transmission connector, and check for short circuit internal to the transmission

If a short circuit is not detected, repair the Transmission Control Module to transmission wiring harness as necessary

If an internal short circuit in the transmission is detected, contact dealer technical support

If the fault persists, check the transmission fluid level using the Jaguar Land Rover approved diagnostic equipment to run the 9-speed ZF - Automatic Transmission Fluid Level Check Application. Refer to the relevant section of the workshop manual and check the automatic transmission fluid quality. For additional information, refer to: Transmission Oil Color Chart - INGENIUM I4 2.0L Diesel/INGENIUM I4 2.0L Petrol (311-01 Automatic Transmission, Diagnosis and Testing).

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

P077B-92 Output Shaft Speed Sensor Circuit - Direction Error - Performance or incorrect operation

NOTE:

Circuit reference - N_OUT / VS_9V / N_T -

Output shaft speed sensor circuit short circuit to ground, short circuit to power, open circuit, high resistance

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Investigate any DTCs relating to ABS faults or any FlexRay comms DTCs and refer to the relevant DTC index

Using the Jaguar Land Rover approved diagnostic equipment, check datalogger signal - Transmission Output Shaft (0x1E68)

Check the integrity of the vehicle driveline and engine mounts. Replace components as required

Check tires for even wear and matched sets and rectify as required

Inspect the wiring harness for damage and rectify as required

Inspect transmission control module connector for damage or water ingress and rectify as required

Refer to the electrical circuit diagrams and check for continuity at the transmission control module connector between circuit(s) VS_9V - N_T and N_OUT. If the circuit is open circuit or high resistance disconnect the transmission connector and check again for continuity internal to the transmission between circuit VS_9V - N_T and N_OUT. If continuity is OK, repair the wiring harness between the transmission control module and the transmission as required. If the circuit IS open circuit or high resistance, raise a Technical Assist (TA) for further support

Refer to the electrical circuit diagrams and check the VS_9V circuit at the transmission control module for short circuit to ground, short circuit to power. If a short circuit is detected, disconnect the transmission connector and check for short circuit internal to the transmission. If an internal short circuit is NOT detected, repair the wiring harness between the transmission control module and the transmission as required. If an internal short in the transmission IS detected, raise a Technical Assist (TA) for further support

Refer to the electrical circuit diagrams and check the N_T circuit at the transmission control module for short circuit to ground, short circuit to power. If a short circuit is detected, disconnect the transmission connector and check for short circuit internal to the transmission. If an internal short circuit is NOT detected, repair the wiring harness between the transmission control module and the transmission as required. If an internal short in the transmission IS detected, raise a Technical Assist (TA) for further support

Refer to the electrical circuit diagrams and check the N_OUT circuit at the transmission control module for short circuit to ground, short circuit to power. If a short circuit is detected, disconnect the transmission connector and check for short circuit internal to the transmission. If an internal short circuit is NOT detected, repair the wiring harness between the transmission control module and the transmission as required. If an internal short in the transmission IS detected, raise a Technical Assist (TA) for further support

If no faults are found with the above checks, check the transmission fluid level using the Jaguar Land Rover approved diagnostic equipment to run the 9-speed ZF - Automatic Transmission Fluid Level Check Application. Refer to the relevant section of the workshop manual and check the automatic transmission fluid quality For additional information, refer to: Transmission Oil Color Chart - INGENIUM I4 2.0L Diesel/INGENIUM I4 2.0L Petrol (311-01 Automatic Transmission, Diagnosis and Testing).

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

P077E-64 Transmission Fluid Temperature Measurement System - Multiple Sensor Correlation - Signal plausibility failure

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transmission control module with the latest level software

Using the Jaguar Land Rover approved diagnostic equipment clear the DTCs and retest

If the fault persists, raise a Technical Assist (TA) for further support

P0780-62 Shift Error - Signal compare failure

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transmission control module with the latest level software

Using the Jaguar Land Rover approved diagnostic equipment clear the DTCs and retest

If the fault persists, raise a Technical Assist (TA) for further support

P0780-93 Shift Error - No operation

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transmission control module with the latest level software

Using the Jaguar Land Rover approved diagnostic equipment clear the DTCs and retest

If the fault persists, raise a Technical Assist (TA) for further support

P07B3-11 Transmission Park Position Sensor/Switch "A" Circuit Low - Circuit short to ground

NOTES:

Circuit reference - L3 / VS_9V

Circuit reference - SENSOR GND

Park position sensor circuit short circuit to ground

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply, if any other transmission faults are set, investigate and rectify them first

Inspect wiring harness for any chafing or damage. Rectify as required

Inspect the transmission control module connector and the transmission connector for signs of water ingress, pin damage and/or corrosion. Rectify as required

Refer to the electrical circuit diagrams and check the L3 and VS_9V circuits for short circuit to ground. Repair the wiring harness as necessary

Refer to the electrical circuit diagrams and measure the resistance between circuit L3 and SENSOR GND and record values. If the resistance value is not in the range of 15K Ohms - 25k Ohms, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07B4-15 Transmission Park Position Sensor/Switch "A" Circuit High - Circuit short to battery or open

NOTES:

Circuit reference - L3 / VS_9V

Circuit reference - SENSOR GND

Park position sensor circuit short circuit to power, open circuit, high resistance

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply, if any other transmission faults are set, investigate and rectify them first

Inspect wiring harness for any chafing or damage. Rectify as required

Inspect the transmission control module connector and the transmission connector for signs of water ingress, pin damage and/or corrosion. Rectify as required

Refer to the electrical circuit diagrams and check the L3 and VS_9V circuits for short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07B9-11 Transmission Park Position Sensor/Switch "B" Circuit Low - Circuit short to ground

NOTES:

Circuit reference - L4 / VS_9V

Circuit reference - SENSOR GND

Park position sensor circuit short circuit to ground

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply, if any other transmission faults are set, investigate and rectify them first

Inspect wiring harness for any chafing or damage. Rectify as required

Inspect the transmission control module connector and the transmission connector for signs of water ingress, pin damage and/or corrosion. Rectify as required

Refer to the electrical circuit diagrams and check the L4 and VS_9V circuits for short circuit to ground. Repair the wiring harness as necessary

Refer to the electrical circuit diagrams and measure the resistance between circuit L4 and SENSOR GND and record values. If the resistance value is not in the range of 15K Ohms - 25k Ohms, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07BA-15 Transmission Park Position Sensor/Switch "B" Circuit High - Circuit short to battery or open

NOTES:

Circuit reference - L4 / VS_9V

Circuit reference - SENSOR GND

Park position sensor circuit short circuit to power, open circuit, high resistance

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply, if any other transmission faults are set, investigate and rectify them first

Inspect wiring harness for any chafing or damage. Rectify as required

Inspect the transmission control module connector and the transmission connector for signs of water ingress, pin damage and/or corrosion. Rectify as required

Refer to the electrical circuit diagrams and check the L4 and VS_9V circuits for short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07D4-07 Transmission Mode Switch "F" Circuit - Mechanical failures

Transmission fluid level low

Transmission control module is not configured correctly

Automatic transmission internal failure

NOTE:

The required repair is dependent on mileage, software, and oil condition

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transmission control module with the latest level

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment clear the DTCs and perform a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07D9-07 Gear 8 Incorrect Ratio - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07DC-07 Incorrect Shift from Gear 1 - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07DD-07 Incorrect Shift from Gear 2 - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07DE-07 Incorrect Shift from Gear 3 - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07DF-07 Incorrect Shift from Gear 4 - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07E0-07 Incorrect Shift from Gear 5 - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07E1-07 Incorrect Shift from Gear 6 - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07E2-07 Incorrect Shift from Gear 7 - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07E3-07 Incorrect Shift from Gear 8 - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07E4-64 Unable to Engage Park - Signal plausibility failure

Park position sensor mountings loose

Valve block internal failure

NOTE:

This DTC can be set by use of the Service Park Release. Cycle the Service Park Release by hand to make sure it isn’t sticking. Return Service Park Release to normal position before continuing with the diagnostic steps detailed below

Prioritized steps to perform:

Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control module for related DTCs and correct those first

Clear DTCs. Test the vehicle up to a normal operating temperature while engaging and disengaging Park with the gear selector

If the DTC is set with engine not running, investigate the Service Park Release. Check that the park position sensor mounting is secured at the correct torque (6Nm) and rectify as required. To gain access to the park position sensor mounting, it is first necessary to remove the ten mounting bolts of the main control valve body and lift the valve body unit from the transmission housing (refer to Automatic Transmission, Removal and Installation, Main Control Valve Body, steps 1 to 5). NOTE: New oil tubes must be installed when the unit is reassembled. The park position sensor is located inside the main casing, adjacent to the electrical connector. The sensor is secured to a boss in the main casing with a screw

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Refer to the electrical circuit diagrams and check the Park Lock Solenoid circuit OUT8 for short circuit to ground, short circuit to power, open circuit, high resistance. Repair the wiring harness as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest

If the fault persists, raise a Technical Assist (TA) for further support

P07E7-07 Stuck in Drive - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transmission control module with the latest level software

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07F6-07 Gear 9 Incorrect Ratio - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P07FA-07 Incorrect Shift From Gear 9 - Mechanical failures

Engine system fault

Accessory drive belt components incorrectly installed

Driveline imbalance

Driveline components excessively worn

Wheel/tire imbalance

Engine mount damaged

Transmission mount damaged

Automatic transmission internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Check the installation of the accessory drive belt components. Rectify as necessary

Check the driveline for debris around rotating components. Rectify as necessary

Check the driveline for excessive wear or backlash. Rectify as necessary

Check the wheels and tires for snow or mud packing and correct balance. Rectify as necessary

Check the engine mounts for damage. Rectify as necessary

Check the transmission mounts for damage. Rectify as necessary

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P0801-94 Reverse Inhibit Control Circuit/Open - Unexpected operation

One or more automatic transmission solenoid circuits short circuit to ground, short circuit to power, open circuit, high resistance

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Using the Jaguar Land Rover approved diagnostic equipment, check the transmission control module for related DTCs and correct those first

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, reconfigure the transmission control module with the latest level software

Using the Jaguar Land Rover approved diagnostic equipment, clear DTC and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P0805-2F Clutch Position Sensor "A" Circuit - Signal erratic

Dog clutch A position sensor contaminated by debris

Transmission control module internal failure

Prioritized steps to perform:

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and perform at least 30 gear engagements (for example D - N - D)

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest

If the fault persists, install a new sensor unit

If the fault persists, raise a Technical Assist (TA) for further support

P0805-64 Clutch Position Sensor "A" Circuit - Signal plausibility failure

NOTE:

Circuit reference - VS_9V / W2 DOG CLUTCH -

Harness fault

Dog Clutch A sensor internal failure

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Inspect wiring harness for any damage. Rectify as required

Inspect transmission external wiring harness to Dog Clutch A sensor. Make sure the connector is securely latched. Rectify as required

Refer to the electrical circuit diagrams and check the VS_9V and W2 DOG CLUTCH circuits for short circuit to power and short circuit to ground. Repair the wiring harness as necessary

Refer to the electrical circuit diagrams and measure resistance between circuit VS_9V and W2 DOG CLUTCH and record values

Inspect the transmission control module connector and transmission connector for signs of water ingress, pins damage and/or corrosion. Rectify as required

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest

If the fault persists, install a new Dog Clutch A sensor

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and retest

If the fluid condition is unsatisfactory, raise a Technical Assist (TA) for further support

Using the Jaguar Land Rover approved diagnostic equipment, clear the DTCs and complete a road test using all gears

If the fault persists, raise a Technical Assist (TA) for further support

P0806-64 Clutch Position Sensor "A" Circuit Range/Performance - Signal plausibility failure

NOTE:

Circuit reference - VS_9V / W2 DOG CLUTCH -

Harness fault

Dog Clutch A sensor internal failure

Transmission control module internal failure

Prioritized steps to perform:

Check battery charge and condition. Record values

Read all DTCs and investigate any DTCs relating to battery voltage supply

Inspect wiring harness for any damage. Rectify as required

Inspect transmission external wiring harness to Dog Clutch A sensor. Make sure the connector is securely latched. Rectify as required

Refer to the electrical circuit diagrams

Found this article helpful?

[ 1 Out of 2 Found Helpful ]

INGENIUM I4 2.0L Diesel/INGENIUM I4 2.0L Petrol, Vehicles With: 9HP50

Found this article helpful?

Related Articles

Still no luck? we can help!

Related Articles

INGENIUM I4 2.0L Diesel/INGENIUM I4 2.0L Petrol, Vehicles With: 9HP50

INGENIUM I4 2.0L Diesel/INGENIUM I4 2.0L Petrol, Vehicles With: 9HP502

INGENIUM I4 2.0L Diesel/INGENIUM I4 2.0L Petrol, Vehicles With: 9HP504

Diagnostic Trouble Code Index - DTC: Body Control Module (BCM)

Diagnostic Trouble Code Index - DTC: Body Control Module (BCM)2